SIZING DATA SHEET - COMPLETE FOR ALL TYPES OF COOLING EQUIPMENT

CUSTOMER NAME: ____________________________________________________________

CONTACT NAME: ______________________________________________________________

PHONE #: ______________________ FAX #: ________________________________________

ADDRESS: ___________________________________________________________________

CITY: ________________________________ STATE: __________ ZIP CODE: ____________

Existing equipment:

Chillers	Comp. HP	Capacity Tons	Type of condenser: Water cooled, Indoor air, Outdoor air cooled
#1
#2
#3

Chiller tank: Tank size L __________________ W ___________________ H ______________

Chiller pump	#1 - HP	___________	GPM	___________	PSI	___________
	#2 - HP	___________	GPM	___________	PSI	___________
Process pump:	#1 - HP	___________	GPM	___________	PSI	___________
	#2 - HP	___________	GPM	___________	PSI	___________
	#2 - HP	___________	GPM	___________	PSI	___________

Cooling Towers	Fan HP	Capacity Tons	Make
#!
#2
#3

Tower tank: Tank size L __________________ W __________________ H ______________

Tower pump	#1 - HP	___________	GPM	___________	PSI	___________
	#2 - HP	___________	GPM	___________	PSI	___________
Process pump:	#1 - HP	___________	GPM	___________	PSI	___________
	#2 - HP	___________	GPM	___________	PSI	___________
	#2 - HP	___________	GPM	___________	PSI	___________

SIZING DATA SHEET - INJECTION MOLDING & BLOW MOLDING

Chilled Water Temperature required: _________________ F

Type of system: Chilling only, with air cooled chillers? _________

Cooling tower and water cooled chillers? _________

Machine #	Clamp Tonnage	Hydraulic motor HP	Type of material	lbs. per hour	Throat cooling
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10

Air compressor;	#1 Motor HP	_____________	Internal cooling:	yes/no
			After cooler:	yes/no
	#2 Motor HP	_____________	Internal cooling:	yes/no
			After cooler:	yes/no
		_____________	Internal cooling:	yes/no
			After cooler:	yes/no

Is the internal cooling on chilled water or tower water?

Is the after cooler on chilled water or tower water?

Other equipment to be cooled or comments: _________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________

Do they use mold temperature control units (TCUs)?

If yes: Heater KW ___________ Pump HP __________ Flow ___________ PSI _____________

Cooling: Direct injection or heat exchanger.

SIZING DATA SHEET - EXTRUSION

Chilled Water Temperature required: ______________ F

Machine #	Screw Dia.	Drive Motor HP	Type of material & lbs./hr	Barrel Cooling	Throat cooling	Gear Box Cooling
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10

Type of extrusion: Pipe _________ Profile ____________ Siding __________Wire __________

Pelletizing: Type of pelletizer - Under water.

- Water ring die face.

- _____________________________________________

Make _____________________________ Model # _______________________

Does the cooling trough have to empty out at start of process?

Air compressor;	#1 Motor HP	_____________	Internal cooling:	yes/no
			After cooler:	yes/no
	#2 Motor HP	_____________	Internal cooling:	yes/no
			After cooler:	yes/no
		_____________	Internal cooling:	yes/no
			After cooler:	yes/no

Is the internal cooling on chilled water or tower water?

Is the after cooler on chilled water or tower water?

Other equipment to be cooled or comments: _____________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
______________________________________________________________________________________

SIZING DATA SHEET - BLOWN FILM

Air Ring Air Temperature required: ______________ F

Entering air: _________________ F dry bulb, _________________ F wet bulb.

Machine #	Air ring CFM	Drive Motor HP	Type of material & lbs./hr	Barrel Cooling	Throat cooling	Gear Box Cooling
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10

Air cooling Units (ACU) are Air to water/glycol coil units:

How many required of each? - External bubble cooling (EBC)

- Internal bubble cooling (IBC)

If IBC is used we require CFM of each unit.

Air compressor;	#1 Motor HP	_____________	Internal cooling:	yes/no
			After cooler:	yes/no
	#2 Motor HP	_____________	Internal cooling:	yes/no
			After cooler:	yes/no
		_____________	Internal cooling:	yes/no
			After cooler:	yes/no

Is the internal cooling on chilled water or tower water?

Is the after cooler on chilled water or tower water?

Other equipment to be cooled or comments: ______________________________________
________________________________________________________________________________
_________________________________________________________________________________
__________________________________________________________________________________